2. 선택 만들기와 사용하기

2.1. 선택 이동하기

Rectangular and elliptical selections have two modes. The default mode has handles on the selection. If you click the selection or press the Enter key,the handles disappear leaving only the dotted outline (marching ants). The other selection tools have different behaviour.

2.1.1. 사각 선택과 타원 선택 이동하기

If you click-and drag a selection with handles, you move the selection outline, and you don't move the contents of rectangular or elliptic selections.

Select the Move tool and set the options to move the selection; the tool supports moving the selection, path, or layer.

그림 7.5. 선택 자체만 이동하기

선택 자체만 이동하기

Most systems support moving the selection using the arrow keys. The precise behavior is system dependent. If the arrow keys do not cause the selection to move, try hovering the mouse cursor over the selection first. Press and hold the Alt (or Ctrl+Alt, Shift+Alt, or Alt). One combination may move the selection by one pixel, and another by 25 pixels each step. Hover the mouse cursor over a side or corner handle, and the arrow keys and combinations can change the size of the selection.

선택 내부에서 조절 영역이 아닌 부분을 클릭하면 새로운 선택이 만들어지고 이제 선택된 영역의 내용을 움직일 수 있게 됩니다.

  • hold down Ctrl+Alt keys and click-and-drag the selection. This makes the original place empty. A floating selection is created. The required key commands may differ on your system, look in the status bar to see if another combination is specified; for example, Shift+Ctrl+Alt.

    그림 7.6. 선택된 영역을 비우면서 선택과 선택의 내용을 이동하기

    선택된 영역을 비우면서 선택과 선택의 내용을 이동하기

  • Shift+Alt 키를 누르고 선택을 클릭해서 끌어놓기하면, 선택된 영역의 내용을 요지하면서 새로운 떠있는 선택이 만들어집니다.

    그림 7.7. 원래 자리의 내용을 유지하면서 선택과 선택의 내용을 이동하기

    원래 자리의 내용을 유지하면서 선택과 선택의 내용을 이동하기

[참고] 참고

On some systems, you must push Alt before Shift or Ctrl. On these systems, pressing Shift or Ctrl first, causes GIMP to enter a mode that adds or subtract from the current selection — after that, the Alt key is ineffective!

2.1.2. 다른 선택 이동하기

올가미, 마법지팡이, 색상으로 선택 등의 다른 선택도구에는 조절영역이 없습니다. 따라서 클릭후 끌어놓기로 선택을 이동시킬 수 없습니다. 이 도구들의 선택 이동은 Alt 키와 화살표 키를 이용해 이동시킬 수 있으며, 선택의 내용의 이동은 사각 선택 도구나 타원 선택 도구와 마찬가지로 Ctrl+Alt 키나 Shift+Alt 키를 누르고 클릭후 드래그합니다.

클릭 후 끌기 대신, 키보드 화살표 키를 이용해 선택 외각선을 이동시킬 수도 있습니다.

2.1.3. 다른 방법

[참고] 참고

선택한 영역을 떠있는 선택으로 만든 뒤 클릭후 드래그나 화살키를 이용해 이동시킬 수도 있습니다. 이런 경우 원래 자리는 비게 되며, 원래 자리를 유지하려면 복사-붙여넣기로 떠있는 선택을 만듭니다.